Siglent · Oscilloscope
Siglent SDS1204X-E software
Remote control and data logging for the Siglent SDS1204X-E oscilloscope, on Windows, Linux and macOS - with the same panel BenchMesh uses for every oscilloscope.
Status
Very likely. Support for the Siglent SDS1204X-E was written from Siglent’s programming manual and follows the same engine as the bench-tested instruments, but nobody has confirmed it on a real SDS1204X-E yet. If you own one, connecting it once and reporting the result moves it to Community-confirmed.
What you can do from BenchMesh
Oscilloscope panel 4 channels
Live readings
- ACQ TYPE
- BWLIMIT
- COUPLING
- DISPLAY
- FREQ
- INVERT
- OFFSET
- PROBE
- SCALE
- SRATE
- TIMEBASE
- TIMEOFFSET
- TRIG LEVEL
- TRIG SLOPE
- TRIG SOURCE
- TRIG STATUS
- TRIG SWEEP
- VAVG
- VPP
- VRMS
Settings you can change
- Acquire type
- Bwlimit
- Coupling
- Display
- Invert
- Offset
- Probe
- Run
- Scale
- Timebase
- Timebase offset
- Trigger level
- Trigger slope
- Trigger source
- Trigger sweep
Connections
- USB-TMC
- USB Test & Measurement Class (USB id f4ec:ee38). No vendor driver needed on Linux; on Windows BenchMesh installs Microsoft’s WinUSB driver with one click.
- LAN (SCPI socket)
- TCP port 5025. Enter the instrument’s IP address.
Sources
The definition was written from these documents (definition siglent_sds1000xe v0.1.0).
- Digital Oscilloscope Series Programming Guide EN02E (Oscilloscope_ProgrammingGuide_legacy.pdf), pages PDF p16 LAN 5025, p24 CHDR, p28-36 ARM/STOP/ACQW/SARA/SANU, p34 SAST, p40 ASET, p42-50 channel, p118 PAVA, p173-174 TDIV/TRDL, p185-194 TRLV/TRMD/TRSE/TRSL, p247-256 WF/WFSU, p309 USB id F4EC:EE38
Have one on your bench?
Connect it, press Detect, try the controls - then tell us how it went. Every confirmation moves a model from “Awaiting” to “Community-confirmed” for everyone.
Questions
- Does BenchMesh work with the Siglent SDS1204X-E?
- Very likely. Support for the Siglent SDS1204X-E was written from Siglent’s programming manual and follows the same engine as the bench-tested instruments, but nobody has confirmed it on a real SDS1204X-E yet. If you own one, connecting it once and reporting the result moves it to Community-confirmed.
- How do I connect the SDS1204X-E to my PC?
- Over USB-TMC or LAN (SCPI socket). USB Test & Measurement Class (USB id f4ec:ee38). No vendor driver needed on Linux; on Windows BenchMesh installs Microsoft’s WinUSB driver with one click. Then press Detect in BenchMesh: it identifies the oscilloscope by its reply and adds it to the bench.
- What can I control on the SDS1204X-E?
- Oscilloscope: set acquire type, bwlimit, coupling, display, invert, offset, probe, run; read acq type, bwlimit, coupling, display, freq, invert, offset, probe.
- Can I log SDS1204X-E measurements to CSV?
- Yes. Right-click any reading to add it to a recording; every instrument on the bench is sampled on one shared timeline and exported as one CSV.
- Is BenchMesh free?
- Yes. BenchMesh is free and open source, for Windows, Linux and macOS, and works offline.