UNI-T · Spectrum analyzer
UNI-T UTS3084T software
Remote control and data logging for the UNI-T UTS3084T spectrum analyzer, on Windows, Linux and macOS - with the same panel BenchMesh uses for every spectrum analyzer.
Status
Very likely. Support for the UNI-T UTS3084T was written from UNI-T’s programming manual and follows the same engine as the bench-tested instruments, but nobody has confirmed it on a real UTS3084T yet. If you own one, connecting it once and reporting the result moves it to Community-confirmed.
What you can do from BenchMesh
Spectrum analyzer panel 1 channel
Live readings
- ATTEN
- ATTEN AUTO
- CENTER
- DETECTOR
- MARKER
- MARKER FREQ
- MARKER LEVEL
- POINTS
- PREAMP
- RBW
- RBW AUTO
- REF LEVEL
- SCALE
- SPAN
- START
- STOP
- SWEEP MODE
- SWEEP TIME
- TG LEVEL
- TG OUTPUT
- TRACE
- TRACE MODE
- TRACE UNIT
- VBW
- VBW AUTO
Settings you can change
- Atten auto
- Attenuation
- Center
- Detector
- Full span
- Marker
- Marker freq
- Peak search
- Points
- Preamp
- Rbw
- Rbw auto
- Ref level
- Scale
- Span
- Start
- Stop
- Sweep
- Sweep time
- Tg level
- Tg output
- Trace mode
- Vbw
- Vbw auto
Connections
- USB-TMC
- USB Test & Measurement Class. No vendor driver needed on Linux; on Windows BenchMesh installs Microsoft’s WinUSB driver with one click.
- LAN (SCPI socket)
- TCP port 5025. Enter the instrument’s IP address.
Notes
- To confirm on first contactLAN port 5025 has no source.
Sources
The definition was written from these documents (definition unit_uts v0.1.0).
- UTS Spectrum Analyzer Programming Manual V1.0 (UTS_Spectrum_Analyzer_Programming_Manual_V1.0.pdf), pages printed p7 *IDN?, p36-37 MARKer MAXimum, p41-43 MARKer X/Y, p51 RLEVel/PDIVision, p62 FORMat / INITiate:CONTinuous, p66 OUTPut, p80-82 BANDwidth, p91 DETector, p93-95 FREQuency, p98-104 POWer:ATTenuation / GAIN:STATe, p107-108 SWEep, p115 SOURce:POWer, p116-118 TRACe:TYPE / TRACe<n>:DATA?
Have one on your bench?
Connect it, press Detect, try the controls - then tell us how it went. Every confirmation moves a model from “Awaiting” to “Community-confirmed” for everyone.
Questions
- Does BenchMesh work with the UNI-T UTS3084T?
- Very likely. Support for the UNI-T UTS3084T was written from UNI-T’s programming manual and follows the same engine as the bench-tested instruments, but nobody has confirmed it on a real UTS3084T yet. If you own one, connecting it once and reporting the result moves it to Community-confirmed.
- How do I connect the UTS3084T to my PC?
- Over USB-TMC or LAN (SCPI socket). USB Test & Measurement Class. No vendor driver needed on Linux; on Windows BenchMesh installs Microsoft’s WinUSB driver with one click. Then press Detect in BenchMesh: it identifies the spectrum analyzer by its reply and adds it to the bench.
- What can I control on the UTS3084T?
- Spectrum analyzer: set atten auto, attenuation, center, detector, full span, marker, marker freq, peak search; read atten, atten auto, center, detector, marker, marker freq, marker level, points.
- Can I log UTS3084T measurements to CSV?
- Yes. Right-click any reading to add it to a recording; every instrument on the bench is sampled on one shared timeline and exported as one CSV.
- Is BenchMesh free?
- Yes. BenchMesh is free and open source, for Windows, Linux and macOS, and works offline.