RIGOL · Power supply
RIGOL DP832A software
Remote control and data logging for the RIGOL DP832A power supply, on Windows, Linux and macOS - with the same panel BenchMesh uses for every power supply.
Status
Very likely. Support for the RIGOL DP832A was written from RIGOL’s programming manual and follows the same engine as the bench-tested instruments, but nobody has confirmed it on a real DP832A yet. If you own one, connecting it once and reporting the result moves it to Community-confirmed.
Note: CH1/CH2 30 V/3 A, CH3 5 V/3 A
What you can do from BenchMesh
Power supply panel 3 channels
Live readings
- CC
- CV
- FAIL
- IOUT
- OCP
- OUTPUT
- OVP
- POUT
- REMOTE
- SBY
- VOUT
Settings you can change
- Current
- Current limit
- Ocp
- Output
- Ovp
- Remote
- Voltage
- Voltage limit
Connections
- USB-serial / RS-232
- 9600 baud, 8N1. Plug in the USB cable (or a USB-RS-232 adapter); BenchMesh finds the port.
- USB-TMC
- USB Test & Measurement Class (USB id 1ab1:0e11). No vendor driver needed on Linux; on Windows BenchMesh installs Microsoft’s WinUSB driver with one click.
- LAN (SCPI socket)
- TCP port 5555. Enter the instrument’s IP address.
Notes
- Interface on some models onlyLAN and RS-232 are fitted on the DP8xxA models; on DP811/821/831/832 they are paid options.
- To confirm on first contactLAN port 5555 comes from community DP832 tools, not the guide.
- Not supported (yet)GPIB only through Rigol's USB-GPIB converter.
- Known issueDP831 CH3 is 0 to -32 V; the voltage setter only offers 0 and above.
Sources
The definition was written from these documents (definition rigol_dp800 v0.1.0).
- DP800 Programming Guide (DP800_ProgrammingGuide_EN_2015.pdf), pages 1-2, 2-8 (Table 2-1), 2-24, 2-34..2-36, 2-52 (Table 2-2), 2-53..2-63, 2-83, 2-90, 2-121, 2-123, 4-2 (USB0::0x1AB1::0x0E11)
- DP800 User's Guide (DP800_UserGuide_EN.pdf), pages front matter (up to 200 W total)
Have one on your bench?
Connect it, press Detect, try the controls - then tell us how it went. Every confirmation moves a model from “Awaiting” to “Community-confirmed” for everyone.
Questions
- Does BenchMesh work with the RIGOL DP832A?
- Very likely. Support for the RIGOL DP832A was written from RIGOL’s programming manual and follows the same engine as the bench-tested instruments, but nobody has confirmed it on a real DP832A yet. If you own one, connecting it once and reporting the result moves it to Community-confirmed.
- How do I connect the DP832A to my PC?
- Over USB-serial / RS-232 or USB-TMC or LAN (SCPI socket). 9600 baud, 8N1. Plug in the USB cable (or a USB-RS-232 adapter); BenchMesh finds the port. Then press Detect in BenchMesh: it identifies the power supply by its reply and adds it to the bench.
- What can I control on the DP832A?
- Power supply: set current, current limit, ocp, output, ovp, remote, voltage, voltage limit; read cc, cv, fail, iout, ocp, output, ovp, pout.
- Can I log DP832A measurements to CSV?
- Yes. Right-click any reading to add it to a recording; every instrument on the bench is sampled on one shared timeline and exported as one CSV.
- Is BenchMesh free?
- Yes. BenchMesh is free and open source, for Windows, Linux and macOS, and works offline.